ECM and FNC

There was a big celebration in Grenoble on Wednesday.: an FNC module is being added to the testing facility to enable technology trials for customers. Why is this so significant? It represents a massive leap in innovation and expands the capabilities of FLEX-type equipment. What are the advantages? Conventional FNC processes are carried out in single-chamber furnaces. However, each process cycle requires opening the chamber, swapping the load, and starting over. To ensure proper operation, the chamber must first be cleared of condensed water vapor, residual water from post-oxidation, and atmospheric oxygen. Since chamber temperatures remain below 750°C, high-temperature desorption isn’t possible, yet the chamber still requires cleaning. Furthermore, because the process relies on a stable nitriding or carbonitriding atmosphere, a portion of the cycle time is dedicated to re-saturating the retort walls. All told, a single process cycle in a single-chamber unit takes 16 hours or more. Additionally, the load is charged into a cold chamber and removed only after cooling below 100°C; the high energy demand is obvious, given that every cycle involves heating and cooling a retort weighing nearly a ton.
In contrast, the FNC chamber on the FLEX system maintains a constant working atmosphere and connects to the vacuum tunnel via a vacuum-tight seal. This allows processing to take place within the chamber independently of the vacuum conditions in the transport tunnel. However, once the nitriding or nitrocarburizing process is complete, the chamber is not exposed to contamination from the external atmosphere. Since the chamber remains heated, there is no time lost to reheating or cooling. Tasks that would take 16 hours in a single-chamber furnace can be accomplished in significantly less time with this setup. It is somewhat reminiscent of the NITROTEC NQ40 technology—also of French origin—which has largely fallen out of use here; that process boasts net cycle times of just 2 to 4 hours, thanks precisely to the continuous saturation of the treatment chamber with ammonia (NH3) and the maintenance of a constant processing temperature.
Naturally, this method of process control improves reproducibility and reliability. Furthermore, it allows for the complete separation of the FNC and post-oxidation processes. Given the flexibility of the FLEX system, one chamber can be dedicated to preheating and pre-oxidation, another to FNC, and a third to post-oxidation. This offers an additional advantage by avoiding the mixing of FNC with steam oxidation. While the latter is a common practice in single-chamber furnaces, the use of ammonia-water imposes a heavy corrosive load on the retort, thereby reducing its service life; with the FLEX system, the service life extends from the typical 4–5 years to at least 10 years.
One of the advantages of NITROTEC NQ40 was the cooling phase following the polymer quench. With the FLEX system, a module for cooling in nitrogen at up to 20 bar can be added, effectively providing super-fast cooling. This not only reduces processing time but also improves the mechanical properties of the part core.
And the applications? Virtually limitless. In practice, this translates to high equipment flexibility, full automation of process steps, and parallel processing that offers significant economic advantages. How that flexibility is utilized is limited only by the customer’s imagination; the same equipment can perform not only FNC but also oil, gas hardening, brazing, annealing, and tempering. That is precisely why ECM markets it under the name “All-in-1“.
If you have a vision for how to leverage this flexibility for your processes, please do not hesitate to contact me. It is certainly the direction that has a future. Don’t have an invitation for the Opening Night? No problem; you can find out more here, for example: https://www.ecm-furnaces.com/icbp-furnaces/nitriding-furnace-ccn/
=======================================================================================================
Are you solving a similar problem? I will help you with the analysis…
40+ years of experience in the field
30+ years of experience… HT-PROGRES, Bodycote, Galvamet
cooperation… VŠB, Czechimplant, ECM Technologies, TAV Vacuum Furnaces, GHC Invest
12+ years of expert activity
Want to ask for a solution or want a non-binding consultation? Click on this link, I will usually respond within 24 hours. Contact email
========================================================================================================
Jiří Stanislav, Ing. CSc.
Consultant and forensic expert
========================================================================================================
29/9/2026













