Logo Jst No Paddings MiniLogo Jst No Paddings MiniLogo Jst No Paddings MiniLogo Jst No Paddings Mini
  • HOME
  • Services
  • E-learning
  • Blog
  • About me
  • Contact
✕
English
  • Czech

Metalco and ASTM E3499-25

Categories
  • Heat treatment shop equipment
  • Quality systems
Tags

Last week, I visited VŠB-TUO. One reason was my work within the NCK (National Competence Centre), but since I knew Metalco was hosting a presentation there on new laboratory instrumentation, I combined the two trips.

So, what did I learn? New equipment was unveiled that evaluates mechanical properties using indentation plastometry based on profilometry (PIP). This method is now covered by standards such as ASTM E3499-25 (Standard Test Method for Indentation Plastometry of Metallic Materials) and DIN SPEC 4864:2019-11 (Test method for the determination of flow curves and benchmark characteristic values ​​for tensile testing by means of minor destructive indentation, 3D measurement, and finite-element material models).

What is it exactly? The principle of indentation combined with inverse FEM analysis has been a subject of research for years—including at the University of Cambridge. In parallel, IMPrintec developed its i3D technology, which was standardized in 2019 via DIN SPEC 4864. Methodologically, it is a physical approach that extracts stress-strain curves—including yield strength and tensile strength—from indentation test data using an inverse finite element method. It sounds mysterious. Unlike conventional hardness testing, local mechanical characteristics comparable to tensile test results are derived from the 3D geometry of the indentation and an inverse FEM model. Simply put:

The indenter is pressed into the material → the 3D shape of the indentation is measured → FEM simulates the indentation → software adjusts material parameters until the simulated indentation matches the actual one → the tensile σ–ε curve is derived from this.

And why FEM—specifically, the inverse finite element method? Normally, we know the material properties and use FEM to calculate the deformation. Here, it is the other way around: we know the deformation and seek the material properties that caused it. To quote a classic phrase, it’s a “neat trick.”

The measurement process requires relatively little surface preparation compared to fabricating a standard tensile test specimen, which reduces turnaround time and costs. And the accuracy? IMPrintec cites a figure of 3.6%.

What does the device look like? IMPrintec manufactures it in several variants. However, the i3D®mBV version also combines HV and HB hardness testing with profilometry.

In this case, in addition to hardness, we obtain Rp0.2 (the offset yield strength), Rm (tensile strength), and the plastic region of the stress-strain curve. While conventional tensile testing involves measurements on a sample separate from the actual component, this method allows for measurement directly on the part of interest. The method cannot determine the fracture characteristics associated with conventional tensile testing—specifically, elongation at break (A) and reduction of area (Z). However, ASTM E3499 does allow for the derivation of uniform elongation (prior to necking). Furthermore, the method cannot be applied if the grain size exceeds one-third of the indentation diameter.

As for applications? Analysis of EBW/LBW/TIG welds and the heat-affected zone (HAZ), comparison of heat treatment effects, local heterogeneity in large forgings, AM Ti6Al4V/IN718, property mapping in AM parts, failure analysis, inspection of actual components from which standard tensile specimens cannot be machined, and optimization of quenching and tempering parameters.

The method is not recommended for cast iron, materials with strong texture, highly anisotropic AM materials, very coarse-grained materials, or gradient layers where the plastic zone spans multiple distinct microstructures. This is due, in part, to the FEM model’s assumption that plastic behavior in tension and compression is approximately symmetrical.

The economic aspect is also compelling. According to calculations presented by the manufacturer, the cost per measurement point can be approximately five times lower than that of a conventional tensile test.

And its applications? They are numerous, though it is not suitable where a tensile test according to EN ISO 6892 is mandatory. However, it is ideal for incoming material inspection, for situations requiring periodic measurements where producing numerous samples is either undesirable or too costly, and—thanks to the availability of portable devices—for inspecting pipelines, large castings, and weldments, or for evaluating the results of stress-relief annealing on large welded structures.

Indentation plastometry is not simply a miniature tensile test. It is a localized experimental measurement combined with the mathematical identification of a material model, from which characteristics comparable to those of a tensile test are derived.

Metalco has once again impressed by targeting the right market segment. Congratulations—this really caught my interest.

=======================================================================================================
Are you solving a similar problem? I will help you with the analysis…
✔ 40+ years of experience in the field
✔ 30+ years of experience… HT-PROGRES, Bodycote, Galvamet
✔ cooperation… VŠB, Czechimplant, ECM Technologies, TAV Vacuum Furnaces, GHC Invest
✔ 12+ years of expert activity
Want to ask for a solution or want a non-binding consultation? Click on this link, I will usually respond within 24 hours. Contact email
========================================================================================================
Jiří Stanislav, Ing. CSc.
Consultant and forensic expert
========================================================================================================

14/9/2026

Related posts

Where is commercial heat treatment heading in the Czech Republic and Slovakia?


Read more

How to define the requirements for selecting a vacuum furnace?


Read more

Heat Treatment Forum 2026 – Wroclaw


Read more

Jiří Stanislav, Ing., CSc.

Consultant for heat treatment of metals

Forensic expert in metallurgy and heat treatment of metals

IČ: 02232413

Elišky Krásnohorské 965
Liberec 14, 46001 Česká Republika

[email protected]

+420 603 235 924

Information

  • General terms and conditions of sale of courses

Cookie settings

Contact

[email protected]

+420 603 235 924

© 2021 tvorbu webu realizoval SEMTIX.cz
    0

    €0,00

    English
    • Czech
    • English

      Cookies on this website

      We use necessary cookies to make the website work (cart, language). With your consent we also use analytics cookies (Google Analytics, Microsoft Clarity) to improve the website and marketing cookies (Google Ads) to measure and target advertising. You can change your choice at any time via “Cookie settings” in the footer. Cookie policy (Czech)